MTP 15HD RS Series |
|
Video |
Gain | Unity |
Number/signal type | 1 set of proprietary analog signals |
Connectors | |
MTP R 15HD RSA D | 1 female RJ-45 on a pigtail |
All other models | 1 female RJ-45 |
|
Video input and loop-through — transmitter (MTP T 15HD RS) |
Number/signal type | 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video 1 buffered RGBHV, RGBS, RGsB, RsGsBs local monitor loop through (includes ID bits) |
Connectors | 2 female 15-pin HD |
Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video |
Minimum/maximum levels | 0.3 V to 1.45 Vp-p |
Impedance | 75 ohms |
Horizontal frequency | 15 kHz to 130 kHz |
Vertical frequency | 30 Hz to 150 Hz |
Return loss | <-30 dB @ 5 MHz |
DC offset (max. allowable) | 250 mV |
|
Video output — receivers (MTP RL 15HD RS, MTP RL 15HD RS SEQ, MTP R 15HD RSA D) |
Number/signal type | |
MTP R 15HD RSA D | 1 analog VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, HD component video, component video, S-video, or composite video |
All other receivers | 1 set of proprietary analog signals 1 analog RGBHV, RGBS, RGsB, RsGsBs, component video, S-video, or composite video |
Connectors | |
MTP R 15HD RSA D | 1 female 15-pin HD |
All other receivers | 1 female RJ-45 1 female 15-pin HD |
Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video 0.7 Vp-p for RGB and for R-Y and B-Y of component video 0.3 Vp-p for C of S-video |
Minimum/maximum levels | 0.3 V to 1.45 Vp-p |
Impedance | 75 ohms |
Return loss | <-30 dB @ 5 MHz |
DC offset | <±20 mV with input at 0 offset |
Skew compensation | 62 ns |
Maximum resolution | Up to 1920x1200 or 2048x1080 or 1080p at 300' Up to 1024x768 at 600' |
NOTE | Refer to the user's manual for the maximum distances recommended for specific resolutions. |
|
|
Sync |
Input type (transmitter) | RGBHV, RGBS, RGsB, RsGsBs |
Output type (receivers) | RGBHV, RGBS, RGsB, RsGsBs |
Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM |
Input level (transmitter) | 3.5 V to 5.5 Vp-p, unterminated |
Output level (receivers) | 4.0 V to 5.0 Vp-p, unterminated |
Input impedance | 510 ohms |
Output impedance | 110 ohms |
Max. input voltage | 5.5 Vp-p |
Polarity | |
Transmitter | Positive or negative (follows input polarity) |
Receivers | Positive or negative (switch selectable) |
|
Control/remote — external device (pass-through, unidirectional or bidirectional) |
Serial control port input/output |
MTP T 15HD RS | RS-232 via (1) 3.5 mm, 3 pole captive screw connector |
Receivers | 1 set of proprietary signals on a female RJ-45 jack |
Serial control port output/input |
MTP T 15HD RS | 1 set of proprietary signals on a female RJ-45 jack |
MTP R 15HD RSA D | RS-232 via 3 poles of a 3.5 mm captive screw connector, 5 pole |
All other receivers | RS-232 via a 3.5 mm, 3 pole captive screw connector |
Baud rates | |
MTP R 15HD RSA D | Up to 38400 bps at up to 1000' (304.8 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.) |
All other models | Up to 38400 bps at up to 600' (183 m) (Higher data rates and distances are possible. Performance varies based on baud rate and cable length.) |
Protocol | Data bits = 5 - 8 Stop bits = 1 or 2 Parity = odd, even, none Flow control = XON, XOFF, none |
NOTE | Protocol is mirrored between the transmitter and the receiver. |
|
Serial control pin configuration | Captive screw connectors: 1 = TX, 2 = RX, 3 = GND |
|
General |
Recommended cable type | CAT 5/5e/6 (shielded or unshielded) |
External Power supply | 100 VAC to 240 VAC, 50-60 Hz, external; to 12 VDC, 1 A, regulated |
Power input requirements | 12 VDC, 0.5 A |
Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
Cooling | Convection, no vents |
Mounting | |
MTP R 15HD RSA D | |
Furniture mount | Yes, using a standard electrical wall box or decorator-style size mud ring |
All other models |
Rack mount | Yes, with optional 1U deep rack shelf |
Furniture mount | Yes, with optional mini under-desk mounting kit |
Pole mount | Yes, with optional pole mounting kit |
Enclosure type | Metal |
Enclosure dimensions | |
MTP R 15HD RSA D | |
Faceplate | 2.6" H* x 1.3" W x 0.24" D
(6.6 cm H* x 3.3 cm W x 0.5 cm D)
*Height is 3.8" (9.7 cm) including mounting tabs.
(Fits the opening in a 1 gang, 4.4" H x 2.7" W decorator-style wallplate. Depth excludes connectors.) |
Device | 2.75" H x 1.65" W x 1.3" D (7.0 cm H x 4.2 cm W x 3.3 cm D) (Depth excludes connectors.) |
All other models | 1.7" H x 4.3" W x 3.0" D (1U high, quarter rack wide) (4.3 cm H x 10.9 cm W x 7.6 cm D) (Depth excludes connectors.) |
Product weight | 0.4 lbs (0.2 kg) |
Vibration | ISTA 1A in carton (International Safe Transit Association) |
Regulatory compliance |
Safety | CE, c-UL, UL |
EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
Product warranty | 3 years parts and labor |
NOTE | All nominal levels are at ±10%. |
|
NOTE | Specifications are subject to change without notice. |
|
(CMS-041917-D11) |