| HSA 200 Series, HSA 222 Series |
|
| Video — HSA 200SE, HSA 200CE |
|---|
| Gain | Selectable: unity (0.7 V), (0.75 V) 50%, (0.8 V) 100% |
| Bandwidth | 300 MHz (-3 dB) |
| NOTE | ID bits are terminated on pins 4 and 11. |
|
|
| Video input — HSA 200S, HSA 200C |
|---|
| Number/signal type | 1 VGA—UXGA RGBHV, RGBS, RGsB, RsGsBs |
| Connectors | (1) 15-pin HD female |
|
| Video input — HSA 200SE, HSA 200 |
|---|
| Number/signal type | 1 VGA—UXGA RGBHV, RGBS, RGsB, RsGsBs |
| Connectors | (1) 15-pin HD female |
| Nominal level | 0.7 Vp-p for RGB |
| Minimum/maximum levels | Analog: 0.3 V to 1.5 Vp-p with no offset at unity gain |
| Impedance | 75 ohms |
| Horizontal frequency | 15 kHz to 135 kHz |
| Vertical frequency | 30 Hz to 170 Hz |
|
| Video output — HSA 200S, HSA 200C |
|---|
| Number/signal type | 1 pass-through VGA—UXGA RGBHV, RGBS, RGsB, RsGsBs |
| Connectors | 5 BNC female on pigtails |
|
| Video output HSA 200SE, HSA 200CE |
|---|
| Number/signal type | 1 VGA–UXGA RGBHV, RGBS, RGsB, RsGsBs |
| Connectors | 5 BNC female on pigtails |
| Nominal level | 0.7 Vp-p for RGB |
| Minimum/maximum levels | Analog: 0.3 V to 1.5 Vp-p |
| Impedance | 75 ohms |
| DC offset | ±5 mV with input at 0 offset |
| NOTE | Output resolution may vary depending on whether or not the Extender is attached to the computer at startup, and also on the type of computer being used. |
|
|
| Sync — HSA 200SE, HSA 200CE |
|---|
| Input type | RGBHV, RGBS, RGsB, RsGsBs |
| Output type | RGBHV, RGBS, RGsB, RsGsBs |
| Input level | 2.0 V to 5.0 Vp-p |
| Output level | TTL: 5.0 Vp-p, unterminated |
| Input impedance | 510 ohms |
| Output impedance | 75 ohms |
| Max. propagation delay | 18.8 ns |
| Max. rise/fall time | 4 ns |
| Polarity | Positive or negative (follows input) |
|
| Audio — HSA 200SE, HSA 200CE |
|---|
| Gain | Unbalanced output: 0 dB; balanced output: +6 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | 0.025% @ 1 kHz, 0.020% @ 20 kHz at nominal level |
| S/N | >90 dB at rated maximum output (21 dB, balanced) |
| Stereo channel separation | >75 dB @ 20 Hz to 20 kHz |
|
| Audio input — HSA 200S, HSA 200C |
|---|
| Number/signal type | 1 stereo, unbalanced |
| Connectors | (1) 3.5 mm stereo female jack |
|
| Audio input — HSA 200SE, HSA 200CE |
|---|
| Number/signal type | 1 stereo, unbalanced |
| Connectors | (1) 3.5 mm stereo female jack |
| Impedance | >10k ohms unbalanced, DC coupled |
| Nominal level | -10 dBV (316 mVrms) |
| Maximum level | +6 dBu, (balanced or unbalanced) at 1% THD+N |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output — HSA 200S, HSA 200C |
|---|
| Number/signal type | 1 pass-through stereo, unbalanced |
| Connectors | (1) 3.5 mm, direct insertion captive screw connector, 3 pole |
|
| Audio output — HSA 200SE, HSA 200CE |
|---|
| Number/signal type | 1 stereo, balanced/unbalanced |
| Connectors | (1) 3.5 mm direct insertion captive screw connector, 5 pole |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Nominal level | Unbalanced output: -10 dBV (316 mVrms)
Balanced output: -2 dBu (632 mVrms) |
| Maximum level (Hi-Z) | >+14 dBu, balanced at 1% THD+N |
| Maximum level (600 ohm) | >+5.5 dBm, balanced at 1% THD+N |
|
| General |
|---|
| Power | |
| HSA 200SE/CE | Supplied by an external power supply |
| External power supply | |
| HSA 200SE/CE | 100 VAC to 240 VAC, 50/60 Hz, external, to 12 VDC, 0.42 A, regulated |
| Power input requirements | |
| HSA 200SE/CE | 12 VDC, 0.2 A |
| Temperature/humidity |
| HSA 200SE/CE | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +3° to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Rack mount | No, but furniture mountable |
| Enclosure type | Metal |
| Enclosure dimensions | |
| CAUTION | Use the appropriate metal Extron routing template or refer to the surface cutout dimensions here before cutting a hole in the furniture or other surface. Pay special attention to the direction the unit will face; the unit's connector access side is underlined. Extron is not responsible for miscut mounting holes. |
|
| HSA 200S, HSA 200SE — USA models |
| Top plate (outer rim) | 6.470" W x 5.125" D
(16.43 cm W x 13.02 cm D) |
| Surface cutout (inside rim) |
| | 5.970 ±0.0325" W x 4.625 ±0.0325" D
(15.16 ±0.083 cm W x 11.75 ±0.083 cm D) |
| Top plate (inside tilt plate) |
| | 4.344" W x 3.000" D
(11.03 cm W x 7.62 cm D) |
| HSA 222S — USA model | |
| Top plate (outer rim) | 6.470" W x 5.125" D
(16.43 cm W x 13.02 cm D) |
| Surface cutout (inside rim) |
| | 5.970 ±0.0325" W x 4.625 ±0.0325" D
(15.16 ±0.083 cm W x 11.75 ±0.083 cm D) |
| Top plate (inside tilt plate) |
| | 4.660" W x 2.875" D
(11.84 cm W x 7.30 cm D) |
| HSA 200C, HSA 200CE — USA models |
| Top plate (outer rim) | 6.500" diameter (16.51 cm diameter) circle |
| Surface cutout (inside rim) |
| | 6.000 ±0.0325" diameter (15.24 ±0.083 cm diameter) circle |
| Top plate (inside tilt plate) |
| | 4.344" W x 3.000" D
(11.03 cm W x 7.62 cm D) |
| HSA 222C — USA model |
| Top plate (outer rim) | 6.500" diameter (16.51 cm diameter) circle |
| Surface cutout (inside rim) |
| | 6.000 ±0.0325" diameter (15.24 ±0.083 cm diameter) circle |
| Top plate (inside tilt plate) |
| | 4.660" W x 2.875" D
(11.84 cm W x 7.30 cm D) |
| HSA 200S, HSA 200SE, HSA 200C, HSA 200CE — USA models |
| Box (under surface) | 4.0" H x 4.6" W (front of unit) x 4.4" D (10.2 cm H x 11.7 cm W x 11.2 cm D) without clamps
4.0" H x 8.0" W (front of unit) x 4.4" D (10.2 cm H x 20.3 cm W x 11.2 cm D) with clamps |
| HSA 222S, HSA 222C — USA models |
| Box (under surface) | 5.6" H x 5.3" W (front of unit) x 3.6" D (14.2 cm H x 13.5 cm W x 9.1 cm D) without clamps
5.6" H x 8.6" W (front of unit) x 3.6" D (14.2 cm H x 21.8 cm W x 9.1 cm D) with clamps |
| HSA 200S/HSA 200SE — international square models |
| Top plate (outer rim) | 8.183" W x 6.375" D (20.79 cm W x 16.19 cm D) |
| Surface cutout (inside rim) |
| | 7.683 ±0.0325" W x 5.875 ±0.0325" D (19.51 ±0.083 cm W x 14.92 ±0.083 cm D) |
| Top plate (inside tilt plate) |
| | 5.90" W x 4.10" D (14.99 cm W x 10.41 cm D) |
| HSA 222S — international square models |
| Top plate (outer rim) | 8.183" W x 6.375" D (20.78 cm W x 16.19 cm D) |
| Surface cutout (inside rim) |
| | 7.683 ±0.0325" W x 5.875 ±0.0325" D
(19.51 ±0.083 cm W x 14.92 ±0.083 cm D) |
| Top plate (inside tilt plate) |
| | 6.183" W x 3.75" D (15.70 cm W x 9.53 cm D) |
| HSA 200C/HSA 200CE — international circular models |
| Top plate (outer rim) | 8.5" diameter (21.6 cm diameter) circle |
| Surface cutout (inside rim) |
| | 8.0 ±0.0325" diameter (20.3 ±0.083 cm diameter) circle |
| Top plate (inside tilt plate) |
| | 5.9" W x 4.1" D
(15.1 cm W x 10.4 cm D) |
| HSA 200 — international, all models |
| Box (under surface) | 4.0" H x 6.3" W (front of unit) x 5.0" D (10.2 cm H x 15.9 cm W x 12.7 cm D) without clamps
4.0" H x 10.0" W (front of unit) x 5.0" D (10.2 cm H x 25.3 cm W x 12.7 cm D) with clamps |
| HSA 222 — international, all models |
| Box (under surface) | 4.5" H x 6.6" W (front of unit) x 4.9" D (11.4 cm H x 16.8 cm W x 12.4 cm D) without clamps
4.5" H x 10.3" W (front of unit) x 4.9" D (11.4 cm H x 26.2 cm W x 12.4 cm D) with clamps |
| Product weight | |
| HSA 200S, HSA 200C | 4.0 lbs (1.8 kg) |
| HSA 222S, HSA 222C | 3.5 lbs (1.6 kg) |
| HSA 200SE, HSA 200CE | 5.0 lbs (2.3 kg) |
| Shipping weight | |
| HSA 200S, HSA 200C, HSA 222S, HSA 222C |
| | 7 lbs (4 kg) |
| HSA 200SE, HSA 200CE | 8 lbs (4 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Listings, certification | UL, CUL, CSA C/US |
| Compliances | |
| HSA 200SE, HSA 200CE | CE, FCC Class A, VCCI, AS/NZS, ICES |
| MTBF | 30,000 hours |
| Warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (7.51-032305-D11) |